Summer corn sowing technique suggestion

First, prepare before broadcast
1. Select fine varieties: such as Zhengdan 958, Nongda 108, Linao 1, Denghai 9, Yongyu 2, etc.
2, drying before sowing. It can kill seeds and increase germination rate.
3, seed dressing before seeding. The use of fungicides or pesticides seed dressing, mix and cool dry hair can be sown. For mixed areas of underground pests and corn diseases, mixed dressings are recommended. Insecticides are mixed with the seed dressing, dried and mixed with fungicides.

Second, sowing
1. Advocate the use of no-tillage sowing techniques, that is, shovel seeding techniques. This type of sowing is provincial, time-saving, and labor-saving. It does not require ploughing, reduces soil erosion, saves the cost of arable land, and increases planting efficiency.
2. When sowing, the sowing volume is generally controlled at 1.5 to 2.5 kg, sowing depth is controlled at 3 to 5 cm, sowing seedlings is too weak and weak, and lightness is not easy to emerge. While sowing, apply a certain amount of fertilizer as a seed fertilizer. If 15 kg per kilogram of potassium carbonate is applied as a seed fertilizer at the time of sowing, corn stalk rot (also known as bacterial wilt) can be effectively controlled. The diseased plant leaves are dark gray-green, with premature senescence and death at the late stage. The ear is drooping and often causes lodging. Therefore, applying a certain amount of fertilizer can not only promote the growth of seedlings, but also prevent and control diseases.
Third, timely watering
The sowing of corn husks is also called robber sowing. Generally, the soil temperature is small. Watering should be timely after sowing to supplement the soil moisture so as to supply enough water for seeds to ensure normal seed germination and seedling emergence.
Fourth, control the growth of weeds
General chemical control, manual control, supplemented by high efficiency and low residue, no side effects of the spray. The best effect is to spray evenly when the ground is wet within three days.
Fifth, suitable time seedling, Dingmiao
After the emergence of corn, the seedlings should be early, Dingmiao should be late. When 3 to 4 leaves are inoculated, the seedlings must be kept in time, leaving two strong seedlings per hole; in 6 to 7 leaves, the seedlings should be seedlings, and the number of mu leaves should be controlled flexibly according to the variety. Such as Zhengdan 958, should be dense planting, 4000 ~ 45000 acres of planting strains; Nongda 108 suitable for sparse planting, 3000 ~ 3500 acres of retained seedlings; Linao No. 1 mu left about 2800 strains. When setting seedlings, weak seedlings, self-crossed seedlings, and diseased seedlings are to be kept, leaving seedlings that are high in height, fine in consistency, and sturdy in stems. Change seedlings into seedlings. If you have seedlings, you can leave two plants before and after. The timing of seedlings and seedlings is controlled at 4 pm on sunny days, and the weak seedlings of the pests are susceptible to wilting after sun exposure for easy identification.
Sixth, control of seedling pests and diseases
1. Laodelphax striatellus and aphids are corn-borne insects. They are sprayed with 50% phoxim or 1000 times metaphorone EC.
2, control of corn virus disease in the corn one leaf one heart period, with 1.5% of diseased Ling II 800 to 1000 times the liquid, spray every 7 to 10 days, followed by 2 times, on both sides of the blade spray.
3, the occurrence of armyworm, control of the barley bite, once the mu with 2.5% trichlorfon powder sprayed with 2.0 to 2.5 kg or 50% phoxim 800 times spray, while curing caterpillars, cotton bollworm Other pests.

Aluminum Die Casting For Power Tools

1) American&European standard

2)OEM&ODM service:It depends on your sample or drawing and meet your requirements for high precision.

3)Power tool series good quality with reasonable price ,timely delivery and great customer service

4) Aluminum Die Casting suitable for Aluminum Die Casting CCTV Camera Housing,Moulds/Tooling,motor casing,pneumatic piston,water pumps,Power tools and other series products.

Aluminum Die Casting For Power Tools production flow:

Mixingâ†’compactingâ†’sinteringâ†’resizingâ†’cleaningâ†’vacuum oilingâ†’packing

Our Advantage

(1)More than 20 years of experience in manufacturing and exporting power tools series.
(2) OEM and ODM service for power tools.
(3) All kinds of castings can be manufactured according to drawing, sample or specific industry standard.
(4) The bes work team makes the best quality
(5) The coordinated service (casting, machining and surface treatment) make better price possible.
(6) Advanced equipments.
(7) Full material testing process and quality control system.
(8) Power Tools quality warranty and on time delivery.

We keep efforts diecasting in long-terms business with our client all over the world, we quite understand what`s the customer real need when they provide drawings and necessary technique require. we can choose the best aluminum die casting power tools production solution to make the component or any design changing if necessary.

Aluminum Die Casting For Power Tools
Aluminium Power Tool Spares,Aluminium Die Casting Power Tool Parts,Aluminum Die Casting For Power Tools,Aluminum Die Casting Bosch Power Tools
Ningbo WEIBO Molding&Machine Co.,Ltd. , https://www.diecasting-manufacturers.com