Tips for using the sprinkler

  The purpose of the sprinkler is to sprinkle water on the road surface and flush the road surface to remove dust and clean the road surface. In addition, it is also used to irrigate flowers and trees used for greening, to increase the use of water for construction, and to extinguish the effects of fire. Suspended pears and sweeping brushes are used to sweep snow in the winter.
 
  Sprinklers are divided into spray type, flush type, and spray-flush type according to the purpose; according to the type of chassis, they are divided into automobile type, semi-trailer type and trailer type; and the water tank capacity can be referred to as a cubic meter (ton) of sprinkler. Such as the Yellow River JN150 car chassis 8.4m3 sprinkler.
 
For highways, urban roads and airport sprinklers, they are mainly installed on chassis with 4t or higher 4t. Its main components include a chassis, a water tank, a piping system, a water pump, a brush and a nozzle. Read the instruction manual carefully before using the sprinkler. Operating strictly according to the requirements of use is an important guarantee for using a sprinkler.
 
1. Requirements for water
 
When the sprinkler uses the river ditch or pond as a source of water, pay attention to that all the ends of the suction pipe are not in the water. In order to avoid inhaling stones or more sand and drift debris, the suction pipe end is generally provided with a filtering device, and it is forbidden to remove the filtering device during the water absorption. If the water source is shallow, it is necessary to dig up the water absorption area in advance so as to ensure that it does not contain impurities and air. The water pump requirements for different sprinklers are different. The clean water pump requires no impurities in the water. The turbid water pump requires no stones and excessive sediment in the water.
 
2. Add water diversion
 
Every time the centrifugal pump absorbs water, a certain amount of water must be added to the pump. After the addition, the water inlet must be closed. When the self-priming pump is used for the first time, it is necessary to add water, and it is unnecessary to add water afterwards.
 
3. The inlet pipe must be vacuumed
 
The water inlet system must maintain a certain degree of vacuum before it can suck water into the tank. The inlet pipe system must be sealed reliably, the hose can not be damaged, the hard pipe can not have cracks, otherwise it will have a phenomenon of air leakage, which will result in the situation that it cannot suck water.
 
4. Parking stalls
 
  Before the water sprinkling vehicle or water sprinkling, the power take-off device must be parked.
 
5. Winter water release
 
Before the advent of winter, the water in the pumps and pipes should be vented to prevent freezing. The northern part of the country is generally no longer under construction during the severe winter. Therefore, after the construction is completed, the water in the pump and the water pipe will be drained immediately to prevent future problems.
 
6. Watering precautions
 
  The front sprinkler of the sprinkler is located at a low position, close to the ground, the spray pressure is relatively large, and can be used for flushing the road surface; the position of the rear sprinkler is relatively high (the sprinkler is generally installed on the left and right sides of the sprinkler), and the sprinkler surface is wide, and can be used for highway construction and watering. When the rear nozzle is used, the front nozzle should be closed; when using the adjustable nozzle, the width of the sprinkler can be adjusted as needed. The wider the sprinkler width, the less the amount of intermediate overlap and the more uniform the sprinkler density.
 
7. Lubrication and fastening
 
During the process of use, lubrication points of the transmission assembly should be regularly lubricated, and the joints should be tightened frequently to ensure normal use.
 
8. Regular sewage
 
  The water tank of the sprinkler truck is provided with a sewage pipe. The inlet of the pipe is the lowest point of the water tank. After a period of use, the discharge pipe switch should be opened periodically to remove the accumulated debris from the tank until the water becomes clear.

Elevator Loading Device

Elevator Loading Device,High Quality Elevator Loading Device,Elevator Loading Device Details, Jiangyin Jiefeng Elevator & Escalator Co., Ltd.

Jiefeng Elevator & Escalator Co., Ltd. , http://www.jyelevatorparts.com