A series of thin metal plates parallel to each other and pressed with a distance column are stacked to form a plate air-Air Heat Exchanger. The main components are heat transfer plates, outer frame sealing plates, compression device and so on.
The plate adopts full welding seal, flue gas and air cross flow between the plate for heat exchange. It`s suitable for air preheating and waste heat recovery in steel, chemical, electric power, battery and other industries, especially suitable for ultra-high temperature air to air heat exchange field.
Tranp`s Plate Air-Air Heat Exchanger is especially suitable for heat exchange between gas medium with high corrosion, high dust and high humidity.
The surface of the heat exchange plate is smooth with strong self-cleaning ability, so it is easy to clean. And multiple process is available, which is customized for different working conditions. Besides, the processing capacity can be as low as ten, but also as high as thousand CBM, therefore it`s widely used in waste heat recovery. What is more, the plate adopts advanced welding equipment and technology, combined use of resistance welding and manual welding between plates ensures that the weld joint is not easy to burst.
Air To Air Heat Exchanger,Air Preheater,Air Preheater In Boiler,Plate Type Air Heat Exchanger Guangdong Jiema Energy Saving Technology Co.,Ltd , https://www.jiemaheatexchanger.com
To hear if the car has any problems, just keep the engine in an idle state and listen to it. If there are abnormal sounds or vibrations, it is often because the tightness of the timing belt of the car is not standard, or the valve clearance may be It is already too big, even because the car has not entered the factory for a long time and it has caused serious knocking or carbon deposition.
If these problems occur, the owner will have to make a decision. If the belt needs to be replaced or adjusted, the natural situation should not be delayed. Although the problem of engine operation will not lead to an immediate crisis, the longer the delay, the more serious the situation will be. The engine will not only The shock is very severe, the car will also consume more fuel, and the life of the engine will naturally be greatly reduced.
Remind everyone that if the belt is damaged, it should be replaced immediately, replacing a belt up to 200 yuan, but if the car speeds up on the road, the belt suddenly breaks, it is not a 200 yuan problem, if serious, may have to go to the factory overhaul .
In addition, when the car is on the road, open the window first and listen to whether there is a strange sound when turning or moving forward. Common noises during cornering often come from the front-wheel drive shaft where the joint has been broken. When you hear intermittent choke, it may be a part of the exhaust pipe that breaks a hole, or which part or part of the bumper has fallen off.
Ten kinds of sound judging methods are the same as human bodies. It takes a long time and it is a long time. If a problem arises, it is normal. The key is how to judge and eliminate it. This is very important for driving safety. There is a "10 sound judgment method" that is worth studying.
1. Impact sound: A heavier metal iron impact sound, it is likely that the engine mount due to severe wear and tear for a long time, the impact will occur when the engine speed changes. However, it may also be caused by damage to the front and rear suspension bushes of the vehicle or due to a low transmission fluid.
2. Tap: The sound is similar to a tap, but the sound is small. When this kind of sound appears, the driver must analyze whether the inferior petrol is used, and if a low-quality oil is used, an explosion sound can also occur.
3. Slamming: The gimbal joint of the drive shaft may be damaged, or it may be caused by small stones in the tire striking the tire or bending the fan blade loose.
4. Buzz: Like a balloon leak, mostly air conditioning or cooling system problems. If the cooling system fails, liquid can be seen at the bottom of the car. In addition, this sound may also occur due to a large leak in the tire or a leak in the engine vacuum chamber.
5. Re-tap: Like a dull knock. This situation is mostly internal to the engine. It may be due to the aging of the vehicle. Bearing or engine valve damage can also be caused.
6. Whistling sounds: Mostly appear when the car turns. It may be that the fan belt is loose or worn. Sometimes there is not enough gas in the tire and this sound also occurs.
7. Squeak: This kind of sound is like the sound of a bee. It is likely to appear as loose parts, plastic or metal parts at the bottom of the engine, and loosening of the fixing brackets of air conditioners or compressors.
8. Roar: From the car with a kind of "Yao Wang ..." call. It is very likely that the ball bearings in the wheels, in the compressor or in the pump are broken, and it is also possible that the air conditioning or the compressor has failed.
9. Tune: Mainly due to the uncoordinated sound of motor aging.
10. Scream: It's harsh and usually there's a problem with the brakes.
Sound heard trailer malfunction
The effort to listen is to protect the car. In fact, this does not necessarily require very sensitive ears. If you listen to your car before you drive away, you may find problems early and avoid the breakdown of the road.