[Xiagong Chusheng Original] On December 28th, 2011, Jimin Industry and Trade Co., Ltd. accepted a WP10 series electronically controlled engine in Shandong. After the replacement of the four supporting equipment, the engine was blown out in a very short time. Based on the actual damages received by the customer, we analyzed the causes of the accident by combining the images of the damaged piston rings: Â Due to the different causes and manifestations of damage to the engine parts, there may be one or more reasons for the same damage, either alone or at the same time. We must analyze the nature of the failure by the surface phenomenon of the parts damage. However, in many cases, the surface damage trace of a part cannot be accurately judged by its nature. It is also necessary to understand the working time, working conditions, operating conditions, maintenance conditions, oil quality, and related parts of the faulty engine. The detailed information of the damage situation and other comprehensive analysis can find the real cause of the failure. â— Accident: Â After the vehicle in this accident was repaired, there was sudden ramming under the condition that the empty car was driving at a high speed. After the incident, the vehicle was towed back to the maintenance company via the trailer. The engine piston showed decentralized damage, and the piston pin showed no sign of high temperature due to poor lubrication; the exhaust valve of the engine was broken, the oil head of the electronically controlled injector was blocked by the small piston block, and the cylinder head face was not severely damaged; There is no deformation in the large end of the rod, but the rod body is bent; the piston pin retainer is intact. Therefore, the detailed configuration of the engine provided by the engine is not known. The coal from Shanxi Province, Luping Road, Shandong Province, the one-way cargo type, is in the state of empty driving on the national highway when a problem occurs. It is rare that this type of abnormal turbulence phenomenon occurs. For current electronically controlled engines, the combustion control is basically completely controlled by a computer, but if you want the engine to work properly, the positional tolerances of the mechanical parts are equally important; for example, the engine's valve clearance, bearing clearance, and even fuel supply. The meshing clearance of the gears in the timing system needs to be strictly performed to perform the factory tuning method. At the same time, because the explosion pressure is much higher than that of non-electronically controlled engines, there are stringent requirements on the strength and high reliability of assembly components. â— Accident analysis: The piston is called the heart of the engine. It is one of the most important parts in the engine. Because the piston is under the effect of high temperature and high pressure gas, it constantly makes high-speed reciprocating motion, so it bears the heat load and mechanical load of high temperature and high pressure. Its working conditions are very harsh. In most Steyr engines, the piston is the only aluminum part of the engine's main moving parts. Any failure of the engine and any related parts or engine operating conditions will most likely result in piston damage or breakage. Therefore, the engine Faults are often exposed on the piston, but the parts that really cause the engine to fail are not necessarily pistons. Specific analysis needs to be made on a case-by-case basis. Many friends face a pile of damaged parts but do not know how to start analysis, in fact, through the phenomenon to see the essence, after grasping enough basic knowledge, as long as careful scrutiny can be partially analyzed! 1. Although the valve of this engine is broken, there is no impact mark on the working plane of the cylinder head. The trace of valve breaking can basically be considered as caused by excessive lateral impact force, but the valve head break zone and valve head work There are no collision marks on the edge of the face. If the valve head is dropped, the valve head is inserted into the piston combustion chamber, for example, because the overall height is increased. For cylinders with an online speed of approximately 7 m/sec. It is almost impossible to have no impact on the cover work surface; then only one case may have a similar phenomenon, and the piston suddenly breaks at work. 2, for the damaged piston, in order to see if there is such a engine, for example, WD615 engine often encountered if the cylinder bore sleeve hole deformation, larger, cylinder sleeve support shoulder stop tilting the case of cylinder sleeve support Damage to the piston caused by shoulder breakage and if the engine is pulled due to a severe cylinder pull in a single cylinder, we will investigate from different locations: The piston did not show any sign of cylinder pull, nor did the phenomenon of high temperature coking from the internal cold oil gallery in the piston block. Judging from the current signs, there are no major flaws in the maintenance process. Looking at the wear condition of the piston pin seat hole, no traces of the impact due to the improper clearance between the seat hole and the piston pin and abnormal wear marks were found. Instead, there was a lateral occurrence of the piston pin end face and the pin seat hole around the part of the residue. Impact marks the formation of. On the contrary, the piston breakage in this accident is more interesting, and most of them are instantaneous tearing states, and the macroscopic observation of the structural level of the end face is relatively loose, which is very different from the normal breakage of the piston formed by several external forces. Piston's billet is marked with Jiangbin Pistons, but it is hard to say that it is a factory part.
[Advantages of α-linolenic acid compared to DHA]
DHA (brain gold) is one of the derivatives of α-linolenic acid. Supplementing α-linolenic acid has advantages over directly supplementing DHA:
Different medical importance: α-linolenic acid is an important nutrient in the 21st century. It is an unsaturated fatty acid necessary for the body. The human body cannot directly synthesize it by itself and must be ingested from the outside world. DHA is not. The human body's own regulation is different: α-linolenic acid is the precursor of DHA, which can provide DHA to the maximum extent according to the human body's needs. However, direct supplementation of DHA is a strong supplement that the human body cannot control itself and is prone to negative effects. Applicable to different groups of people: α-linolenic acid is helpful in regulating blood pressure, blood lipids, and blood sugar, while DHA comes from fish oil. Pregnancy-induced hypertension inevitably contains animal cholesterol, and women with gestational hypertension, obesity, and overweight cannot use it. use. The "Usage" of the secondary directory is modified to:
Direct drinking: average daily dose of 5-10 ml; drop on warm rice, bread or steamed buns, reduce to 1-5 ml for children.
Smart salad dressing: Add to cold dishes or salads.
Soup seasoning: drop into cooked porridge, soup, and milk.
Baked pastries: Use organic nutritious oils instead of hydrogenated oils or butter in baked pastries.
Homemade preparation: mix it with ordinary edible oils such as soybean oil, peanut oil or rapeseed oil in a ratio of 1:5-1:10 before consumption.
Secret combination: Take 5-10 ml of nutritious oil and mix it with sugar-free homemade yogurt or sugar-free yogurt before eating. It is a popular anti-cancer food therapy in Europe and the United States.
Jilin Chunyi Industrial Co., Ltd , https://www.jlxytruckpart.com