One tow two wreckers, also known as flat wrecker , is characterized by a flat car can carry a car, the towing device can lift the front wheel of another car, the rear wheel landing at the same time evacuation traction. Below, Xiagong Chu Sheng Wu car manager to explain in detail for everyone: the detailed operation steps of the flat wrecker flat panel loading vehicle. 1. First, the flatbed wrecker must be lifted and moved to a straight line with the towed vehicle. Then slowly tilt the flatbed to the ground. If the ground is not flat, you need to place a transition plate at the contact between the flatbed and the ground. Avoid too much effort when towing the vehicle. 2. Remove the wrecker's winch clutch, pull out the wire rope to hang the J-hook on the tow hook of the wrecker, and then combine the clutch of the wrecker's winch. Note: When pulling out the steel rope, the number of steel ropes left is not less than 3 turns. 3. Hang the stalled vehicle's gear to the neutral position and release the parking brake of the removed vehicle. 4. Control the wrecker winch lever, pull the towed vehicle onto the platform, and control the J-hook on the wire rope, and keep the distance from the winch more than 0.4m. 5. After the wrecker has been dragged onto the upper plate, tie the rear tire of the towed vehicle with the fastening tape provided with the vehicle, and tighten the solid belt diagonally to the rear and both sides to make it hang in the two. Side flat ring on the ring. 6. When a flat wrecker is used to secure a faulty car with a fastening safety strap on the flat plate, four straps must be locked on the wheel or the car body respectively. 7. When the strap is locked, the ratchet must be closed. 8. Control the tilting lever of the flat panel so that the tail of the wrecker will rise 0.15m above the ground. 9. Control the wrecker flat tilting joystick to move the platform forward to about 0.6m away from the front end. The control platform tilts the joystick to return the platform to the horizontal position. 10. Control the flat slide joystick to move the wrecker flat to the front. 11. In order to prevent the wrecker from driving, because the tension of the vibrating wire rope may cause damage to the winch, the other two safety chains must be used to fix the front end of the vehicle according to the above method, and tighten as much as possible to make it loaded and positioned. 12, will be loaded on the car to hang a file, pull the handbrake. 13. Check that all seatbelts or chains and connections are secure and tightened. 14. After the above steps are completed, the following working procedures of the wrecker can be performed: the clutch of the wrecker is pressed, the power take-off is disengaged, and the platform loading operation is completed. 100kg/h Potato Chips Production Line 100Kg/H Potato Chips Production Line,Potato Chips Making Line,Potato Chips Production Machinery,Machine Line For Potato Chips Zhucheng Lijie Food Machinery Co., Ltd. , https://www.lijiegroup.com
note! ! When the winch is under load, do not disconnect the manual control clutch of the winch! ! This will damage the winch.
note! ! When using a winch to pull an accident vehicle, especially a car with a relatively low chassis, be very careful not to damage the front part of the trailer, so as not to cause unnecessary trouble.
Note: If the rigid safety bail is broken, the fastening straps should be wrapped around the sturdy parts of the car. For fastening straps that cannot be manually locked, the winch lever can be used to maneuver the winch to move the loading vehicle forward a little to tighten the fastening strap properly.
note! ! Nylon straps tend to loosen for a long period of time. During the operation, the tightness of the bandage should be checked at regular intervals. In particular, in the case of poor road conditions or sudden braking, check the tightness of the fastening straps to avoid accidents. .
A detailed explanation of the operation steps of a wrecker truck
A detailed explanation of the operation steps of a wrecker truck