"China's manufacturing industry is facing double squeeze. Enterprises that do not implement smart manufacturing may disappear in the next five to ten years," said Li Dong, deputy director of the Ministry of Industry and Information Technology and director of the National Major Technical Equipment Office in Chongqing on the 22nd. The first China (Chongqing) International Intelligent Manufacturing Technology and Equipment Fair was opened in Chongqing on the same day. At the “International Smart Manufacturing Summit†held here, experts and scholars from home and abroad, and representatives of companies focused on topics such as green, smart and product innovation. Interactive exchanges, together look forward to the development prospects of the industry. According to the statistics of the World Bank, China's manufacturing industry increased by USD 3.2 trillion in 2014, and 220 industrial products ranked first in the world. Since 2011, China has become the world's largest manufacturing country for five consecutive years. However, China's manufacturing industry has problems such as weak independent innovation capability, outstanding product quality problems, weak industrial infrastructure, and low level of information technology. Regarding the many shortcomings of "Made in China", Li Dong analyzed that China's manufacturing industry is facing "double squeeze." Looking specifically at internal factors, China's economy has entered a period of moderate growth with a period of rapid growth, and low-end industries have gradually lost competitiveness. The economic development mode of the previous period was not sustainable. From an external point of view, developed countries in Europe and the United States have adopted the "reindustrialization" strategy, seeking to continue to lead the industry in terms of technology and industry, seizing the high end of the manufacturing industry, and further distance from China. At the same time, developing countries such as India and Vietnam have to accept labor-intensive industries for lower labor costs and seize the low-end market for manufacturing. "In this case, smart manufacturing will inevitably trigger changes in China's manufacturing industry." Li Dong said, including product intelligence, intelligent production processes, intelligent management, etc. will be the development trend of China's manufacturing industry. In this transformation, enterprises must exert their enthusiasm and endogenous motivation to solve the problems of product technology, price, and energy consumption brought about by market competition. Through the implementation of smart manufacturing, enterprises can enhance the overall competitiveness of China's manufacturing industry. Smart manufacturing will trigger a new round of industrial revolution and foster new production methods. Qu Xianming, director of the Manufacturing Research Office of the Chinese Academy of Engineering, agrees with Li Dong. Qu Xianming once participated in the formulation of the "Made in China 2025" plan. In his view, besides the enterprises' own efforts, the transformation and upgrading of China's manufacturing industry also requires the government to provide directional guidance for smart manufacturing, and formulate corresponding fiscal, taxation, innovation, and demonstration promotion. , industrialization and other policy measures to encourage companies to implement smart manufacturing. “This will help to mobilize the strength and resources of governments at all levels and in all walks of life, form a situation of linkage between the two sides, focus on the effective use of all aspects of advantageous resources, and promote the intelligent transformation of China's manufacturing industry,†said Qu Xianming. Xu Honghai, president of the Shanghai Institute of Industrial Automation Instrumentation, suggested that the implementation of smart manufacturing in China's manufacturing industry must proceed from reality. It is necessary to promote the whole industry as well as to guide the classification. Some enterprises must also pay close attention to the automation and digitalization course. The conditions are good. Enterprises should move toward higher goals and strive for the first breakthrough. ①Hardness:
Due to the scientific synthesis of high-molecular polyurethane elastomer materials using iron rubber, the higher the hardness, the higher the modulus, the smaller the elongation, and the better the wear resistance and heat resistance. Well, in the range of minus 35 degrees Celsius to 100 degrees Celsius, and at a pressure of 60 to 70 MPa, the maximum sealing performance can be guaranteed.
The use of viscoelastic seals made of nitrile rubber is the most complete protection against damage caused by back pressure. In the range of minus 55 degrees Celsius to 100 degrees Celsius, and under a pressure of 21MPa, due to the rubber The seal is often in a compressed state, so the compression performance of the rubber seal must be considered. It not only achieves enhanced anti-climbing performance and low friction resistance, but also has good performance in dealing with special low-temperature oil, and can also be used in combination with Anti-wear Ring double-purpose retaining ring BRL type.
Sealing products made of polytetrafluoroethylene and nitrile rubber/PTFErubber; or seals made of nylon resin and nitrile rubber, which can be used in a wide range of applications with large pressure changes and fast sliding speeds According to the working condition, the input hydraulic pressure cutout is designed on the end face of the polytetrafluoroethylene ring to prevent penetration leakage. The maximum working temperature environment is minus 40 degrees Celsius to 160 degrees Celsius; the maximum working pressure is 50MPa.
oil seals,hydraulic oil seal,track link oil seal,TCV oil seal,O-ring Safe Seal Technology Co., Ltd. , https://www.jsspreals.com
SPGW piston seal
Material:PTFE+rubber elastomer+reinforced modified nylon
Temperature:Nitrile rubber -40~100℃
Speed:=1.0m/s
Pressure:≤50mpa
SPGO piston seal
Material:PTFE+rubber elastomer
Temperature:Nitrile rubber -40~110℃
Speed:=1.0m/s
Pressure:≤35mpa
SRUV piston rod seal
Material:NBR+thermoplastic polyurethane
Temperature: -35`90℃
Speed:=0.5m/s
Pressure:≤40mpa
SRS piston rod seal
Material:PTFE+NBR
Temperature:-40~110℃
Speed:=1.0m/s
Pressure:≤40mpa
SRCB piston rod buffer seal
Material:Polyurethane+modified polyoxymethylene
Temperature: -35~110℃
Speed:=1.0m/s
Pressure:≤50mpa
SRU piston rod seal
Material:Polyurethane
Temperature:-35~100℃
Speed:=1.0m/s
Pressure:≤40mpa
SRD iron case dust prevention
Material:Polyurethane+metal skeleton material
Temperature:-40~110℃
Speed:=1.0m/s
SRDI soft dustproof
Material:polyurethane
Temperature:-40~110℃
Speed:=1.0m/
SDS Dumbbell Seal
Material:polyurethane
Temperature: -35~110℃
Speed:=0.5m/s
Pressure:≤50mpa
SPG piston combination seal
Temperature:
NBR+Polyurethane + Modified Polyoxymethylene
Temperature:-35`110℃
Speed:=0.3m/s
Pressure:≤70mpa
SRNL piston rod seal
Material
NBR+Polyurethane + Modified Polyoxymethylene
Temperature:-35`110℃
Speed:=0.3m/s
Pressure:≤70mpa
SRDF Piston Rod Seal
Material
Polyester rubber
Temperature:-40`100℃
Speed:=1.0m/s
SDY Y-seal
Material:Polyurethane
Temperature:-35~110℃
Speed:=0.5m/s
Pressure:≤70mpa
KZT anti fouling ring
SDS Steffel
Piston main oil seal