Structure and use of cold and heat shock test box

Structure and use of cold and heat shock test box

The hot and cold impact test box is used to make product test structures and complex materials. It instantly circulates extremely high temperatures and extremely low temperatures. Products change at high and low temperatures in a short period of time, and the products are tested under high and low temperature conditions. Tolerate the degree of chemical change or physical damage caused by thermal expansion and contraction in a short time. The objects of use include metal, plastics, rubber, electronics and other necessary test equipment for the material industry. They are used to test material structures or composite materials, and test equipment necessary for the material industries such as metals, plastics, rubber, and electronics to test the material structure or Composite materials can serve as a basis or reference for product improvement.

The hot and cold impact test box is divided into three box type and two box type. The three box type hot and cold impact test box is divided into three parts: high temperature zone, low temperature zone, and test zone. The temperature in high temperature zone or low temperature zone passes through the impact. The high pressure cylinder drive enters the test area for temperature shocks to achieve temperature polycondensation. The high-temperature zone and the test zone were tested for preservation of temperature during high temperature, and the low-temperature zone was closed. When the low temperature zone is tested, the temperature cycle is maintained during the low temperature period and the test zone, and the high temperature zone is closed. Test products are dynamic.

The two-box cold and hot shock box is divided into two parts: the high-temperature zone and the low-temperature zone. The sample is placed in the basket. When the basket is impacted, the test product is moved to the high temperature zone or the low temperature zone for impact. The test product is a dynamic type.

The system can do automatic cycle impact or manual selection of impact. The cooling system adopts two cooling systems. The cooling effect is fast and the cooling mode is water-cooled or air-cooled.

Highest temperature and lowest temperature

High temperature: 150°C

Low temperature: F type -40°C ~ 150°C X -55°C ~ 150°C S -65°C ~ 150°C

Test chamber temperature range

Test high temperature zone temperature range: 60°C ~ 150°C Test zone cryogenic temperature range: -10°C ~ -40°C

Exposure time

High temperature exposure time: +60°C ~ 150°C 30 minutes

Low temperature exposure time: -10°C (F-40°C X-55°C S-65°C) for 30 minutes

Regenerative tank heating time: RT ~ 200°C Approx. 45 minutes

Cooling tank cooling time: RT ~ - 75°C about 100 minutes

Temperature recovery time/transmission time: ≦5min/≦5sec

Temperature Control Accuracy/Distribution Accuracy: ±0.5°C/±0.2°C

Defrost function

Automatic/manual defrosting can be set

Internal and external materials

Inner material is 304 stainless steel The outer box material is stainless steel or cold rolled steel sheet paint.

Insulation material is rigid foam and glass wool

cooling system

Original German Bisel semi-enclosed compressor (water-cooled)

Original French Taikang Brand Sealed Compressor (Air-cooled)

Safety protection device

No fuse switch, compressor high and low voltage protection switch, fault warning system, electronic alarm

Power AC380V 50/60HZ

Cold Drawn Steel Bar

Cold drawn steel bar is produced by Hot Rolled Steel Bar or wire rod to get smooth surface, more precision size, higher mechanical properties, which improves machining characteristics. It can also get various sections and sizes. So cold drawn steel bar is a better choice for machining users.

According to different steel grade, the production line is usually different. The Basic production line is as below:

Cold Drawn Steel Bar

For high carbon steel or alloy steel bars, to avoid the cracks in inner or surface, the bars are usually required to be annealed before cold drawing.

To get different mechanical properties or hardness depending on final usage, the cold drawn bars will also be heat treated such as annealed, normalized or quenched and tempered(Q&T).

For CNC machines usage, to get much more precision sizes or much more better surface roughness for chrome plating, the cold drawn steel bars can also be centerless ground or polished.

We have more advantages on producing cold drawn steel bars:

1) Big stocks of hot rolled round bars or wire rods as raw materials

2) Wide range of cold drawn steel bar sizes: from 10mm to 150mm

3) Different cold drawing medias powder or oil to get different surface

4) Straightening machines to get better straightness up to 0.5mm/m

5) Grinding and polishing machines to get better roughness upto 0.4um

6) Heat treating furnaces to adjust the mechanical properties

7) Full sets of testing equipment to test the sizes, mechanical properties and microstructure.

8) Multiple packages to avoid broken packages and anti-rusty

Cold Drawn Steel Bar,Cold Drawn Steel Rod,Cold Drawn Steel,Cold Drawn Steel Bar Manufacturers,Cold Drawn Steel Properties

SHANDONG LE REN SPECIAL STEEL CO., LTD. , https://www.sdbrightsteelbar.com