Four erroneous behaviors accelerate the aging of high and low temperature test boxes

"The high and low temperature test boxes are useless for several years, but the losses are particularly large." Actually, the wrong behavior that we frequently neglect in daily use is to accelerate the "aging" of high and low temperature test boxes. The technical director explains to you the several kinds of damage that the high and low temperature test box fears.

High and low temperature test box door often switch. Routinely, the number of opening of the test chamber should be reduced as much as possible. Frequent opening of the door will increase the loss of cooling in the test chamber, affect the cooling effect, and increase the energy consumption.

Deactivate high and low temperature test boxes for a long time. For some reason it is not necessary to do the test, the user will choose to let the test box “rest”, but the manufacturer reminds, generally do not disable the test box for a long time, otherwise it will affect the life span, it should be running for one hour after a period of time, This can greatly increase the life and performance of the test chamber.

High and low temperature test box

High and low temperature test box power outlets are free to pull. When the test chamber is in normal use, the temperature in the test chamber reaches the set value, and the thermostat automatically cuts off the power supply. At this time, the high and low pressures in the refrigeration system are already balanced. For the compressor, the load is small and the motor is easy to operate normally. start up. If the power is forcibly cut off, the power supply is turned on immediately when there is a relatively high pressure difference in the refrigeration system. The high-voltage power difference causes the motor load to be too large and the starting current is 8 to 10 times the normal value, which is easy to over current. And the motor was burned. The manufacturer emphasized that after the test box is powered off, it should wait for 3 minutes. After the refrigeration system's high and low pressures reach equilibrium, the power supply is reconnected.

High and low temperature test box cleaning agent is not properly selected. When cleaning the test box, in order to prevent damage to the outer coating of the box and the stainless steel parts in the box, do not use washing powder, decontamination powder, talcum powder, alkaline detergent, boiling water, brushes, etc. to clean the inspection box to prevent damage to the tank or Pipeline. First cut off the power supply, use a soft cloth dipped in water or dishwashing detergent, gently scrub, and then wipe the detergent with water. When cleaning, take care not to touch the electronic components in the inspection box to ensure the safety of electricity. After cleaning, plug in the power plug and check that the temperature controller is set to the correct position. Refrigerator is good once a year every year.

CNC Hydraulic Flat Bar Punching, Marking & Shearing Machine 

CNC Hydraulic Punching Machine for Plates

POWER: Three phase four wire systems

   AC Voltage: 380 V /415 V

   Fluctuation of voltage: ±5%

   Frequency: 50Hz

   Local working temperature: 0-40℃

sample

Used for punch and mark of joint plate in the field of iron tower. It is also used to punch and mark metal plate of other trade.

Unloading Conveyors

feeding channel

The Feeding Conveyors (Double linear guide with rack gear in middle, high precision)

The Feeding Conveyors (Double linear guide with rack gear in middle, high precision)

Y Axis Main Machine Wove Back And Forth By Double Linear Guides

Y Axis Main Machine Wove Back And Forth By Double Linear Guides

Double leaner guides feeding and NC feeding carriage

Automatic Feeding Carriage

carriage

Work Pieces

2

Product Feature:

1. The machine-frame is made by C-type plate welding, with good rigidity and big handling space. The machine sets three die-stations (among them, one is the marking die-station), automatic switching die-stations. Clamping system can adapt to different work piece, with zero baffles as datum mark, and work piece supported by rolling-ball working table. Axis X & Y action should be controlled by servo motor and ball-screw driving, and double-axis CNC system controls the position of punching, so as to make the whole machining process automatically; operator may input the sizes of work piece to computer for repeated calling program in the future.
2. Adopt CNC technology, servo motor in feeding, with high efficiency, stable work piece precision.
3. Important functional components adopt modular assembly, easy to repair it.
4. Carry out punching, marking and drilling on the one plate.
5. Drilling unit has the functions including rapid falling, slow work-feeding and quick feeding back to improve working efficiency.
6. Easy programming, may input the diameter of holes, position and the quantity of work piece to computer, and also may use the program generated by lofting software, or adopt direct conversion CAD/CAM.
7. With function of self-diagnosis for failures.
8. Lighten the working strength of workers.


Our Service

Installation:

The seller shall send one engineer to the buyer's country for installation, commissioning and training. The buyer is responsible to provide all necessary equipments for handling and lifting the machine parts before seller's engineers go to the buyer's plant. In addition, the buyer should provide workers to support in installation activities, under supervision from the seller's engineers.
 

Commission:

The Supplier should give drawings and other details of material/preparation required for installation of machinery which the buyer has to prepare and keep ready before the machine arrives at the buyer's factory. Installation and commissioning can be finished within 5-10 days for above machine generally. 
 

Training:

Training will include training on computer programming, machine operation and troubleshooting. The training time is at most 5 days for this machine. 
The buyer should arrange no less than two people for accepting training. After training, the buyer should sign the "Receiving & Inspection Report" supplied by the seller to demonstrate the successful finish of commissioning and acceptance of the buyer.

Our Company

Factory: 

With the development of SUNRISE, now our company has occupied important position in this industry. Due to the orders and sales performance is continuously improving, in order to better development, to meet customer's demand, and to provide customers high-quality equipment with the shortest time, our company have bought the new site, the area about 50,000 square metersthis will make sufficient preparation for development of our company and every customer. 
 

Workshop:

Quality make brand, honesty win market, harmony converge talents, and innovation promote development. Our ability to consistently provide innovative, high quality products that outlast and outperform the competition, is why we are the one of the most successful companies offering the most advanced and productive solutions in the CNC machine industry.
 

Warehouse:

Manufacturing customer oriented products has always been our supreme concern. We believe that quality is the soul of an enterprise forever. Therefore, we never compromised with the quality of our products. We adopt advanced, scientific modern management ideas and system to realize supervisory control among all aspects of produce, inspection, sale and service etc., which help control quality, increase work efficiency and guarantee products' stability, reliability and precision. Therefore, the enterprise can achieve rapid and sustainable development.  
 

Team:

We are a team of experienced and dynamic professionals who are experts in handling precision work through scientific processes. The professional excellent talents unite a powerful and creative team of design, research and development, which build our solid technical strength and competitiveness. And our company is developing fast and supply specialized service to all customers.


Our Certifications
SUNRISE is focus on quality and company's image. We win market with good quality and service. The company has already passed International Quality Management System ISO9001:2008 certification for many years and also got the CE certificate, smoothly got the title of High and New Tech Enterprises. And has more than ten own intellectual property rights and patent technology. We have own import and export right. Our products exported to Russia, South Asia, South east Asia, Middle East, South America, Africa, Australia, Eastern Europe etc.

Flat Bar Punching Machine

Flat Bar Punching Machine,Flat Plate Punching Machine,Flat Bar Shearing Machine, Flat Bar Hydraulic Press Machine

Shandong Sunrise CNC Machine Co., Ltd , https://www.scmcnc.com